![Solenoid on garden tracker](https://loka.nahovitsyn.com/191.jpg)
![solenoid on garden tracker solenoid on garden tracker](https://i0.wp.com/www.moparpartsinc.com/images/parts/Chrysler/fullsize/00i99522.jpg)
In this case, the battery’s negative is connected to the metallic screw plate of the 3-post solenoid. If the solenoid is a 3-post solenoid, no separate connection is available to attach the battery’s negative terminal. To carry out this test, you first need to connect the available battery’s negative terminal to the solenoid’s negative. The testing methods for the 3-post and the 4-post solenoid are the same, so no need to worry about that! – Step I: The “click sound” test using a 12 V battery: The testing method is carried out by using a 12V battery source and a multimeter. Test the solenoid using a multimeter and as 12V battery source: Since the solenoid has been detached, now it’s time to test it. Taking a good photo from your phone before removing the solenoid’s connections is also a great option so that it may help you reconnect the solenoid correctly. Rotate the starter solenoid forward and pull it out from the lawnmower. Next, remove the starter solenoid mounting bolt from the mower’s frame. Also, pull the wires from the coil spades. Remove the wires connected to the terminals of the solenoid. You shall see a solenoid now, attached to the lawn mower’s metal body via some screws. – Step II: Removing the solenoid from the lawnmower: Next, remove the retaining tabs and lift the battery box out of the mower’s body. Take the battery out of the battery box and release the seat switch wire clip from the seat bracket. Similarly, remove the positive terminal from the battery. Now, lift the seat and remove the negative terminal from the battery. Firstly, turn the ignition switch off and remove the key. The solenoid is usually located below the battery, on the bottom left of the mower. – Step I: Removing the battery from the lawnmower: To check the root cause of the solenoid’s malfunctioning, it must be removed from the lawnmower first. The lawnmower solenoid may get defective with time because its terminals may get rusty due to moisture present in the air, or the metal plate inside the solenoid may have stopped working. Removing the solenoid from the lawnmower: The procedure below explains all the necessary steps to test the solenoid and replace it with a new one if worn out to ensure that the lawnmower goes up and running again.
![solenoid on garden tracker solenoid on garden tracker](https://greenseedgarden.com/wp-content/uploads/2018/06/8186-fmr35n-800x800.jpg)
1.2.2 – Step II: The connectivity test using a multimeter:.1.2.1 – Step I: The “click sound” test using a 12 V battery:.1.1.2 – Step II: Removing the solenoid from the lawnmower:.1.1.1 – Step I: Removing the battery from the lawnmower:.Step 5: Test the lawnmower with the new solenoid.Step 3: Purchase a new solenoid if the test fails.Step 2: Test the solenoid using a multimeter and a 12V battery source.Step 1: Remove the solenoid from the lawnmower.
#Solenoid on garden tracker how to#
How to test a lawnmower solenoid and replace it: The testing methods used to test these solenoids are the same. The solenoid may be a 3-post solenoid or a 4-post solenoid. The solenoid may often deteriorate as it’s service life may end, or it’s terminals may get damaged due to corrosion. It’s attached to the lawnmower’s metal body via screws. Lawnmower solenoid is usually located at the bottom left side of the vehicle below the battery. This blog will help you how to test and replace your lawnmower’s solenoid and replace it if it’s faulty. But you don’t want to take the lawnmower to a mechanic who might charge you a lot for testing the solenoid. After some checking, you think that the problem is either with the battery or the lawnmower’s solenoid. One fine day you plan to cut your lawn, but as soon as you start your lawnmower, nothing happens.
![Solenoid on garden tracker](https://loka.nahovitsyn.com/191.jpg)